Grid view List view

Showing 469–480 of 3716 results

GE DS200LDCCH1ANA

¥12,999.00

Product Parameters

Parameter Category Specification Details
Brand & Model GE DS200LDCCH1ANA
Product Series Mark V Control System Spare Part
Operating Voltage 24V DC ±10%
Input/Output Channels Configurable digital I/O channels (varies by system setup)
Communication Protocol Supports GE Proprietary Protocol, Modbus RTU
Operating Temperature Range -40°C to 70°C
Storage Temperature Range -55°C to 85°C
Humidity Tolerance 5% – 95% (non-condensing)
Dimensions (L×W×H) Standard industrial form factor (150mm×100mm×50mm, subject to verification)
Weight Approx. 0.8kg
Certification UL, CE, ISO 9001 Certified

GE DS200ADMAH1A

¥2,599.00

Product Parameters

Parameter Name Specific Specifications
Brand & Model GE DS200ADMAH1A
Product Type Industrial-grade high-reliability digital input module
Input Channels 16 independent digital input channels
Input Signal Type Dry contact input, compatible with NPN/PNP sensors (configurable)
Input Voltage Range 24VDC (±10%), wide-voltage adaptation: 19.2VDC ~ 30VDC
Input Current Typical value: 5mA @ 24VDC; Maximum: 8mA
Response Time Standard mode: ≤1ms; High-speed mode: ≤0.2ms (configurable)
Input Impedance ≥1kΩ
Operating Voltage 24VDC (±10%), supports redundant power supply
Power Consumption Typical: 6.5W; Maximum: 8.2W (full load)
Operating Temperature -40℃ ~ +70℃
Storage Temperature -55℃ ~ +85℃
Relative Humidity 5% ~ 95% (non-condensing, altitude ≤ 2000m)
Protection Level IP20 (module body); Optional front panel IP40 protection
Isolation Method Channel-to-channel electrical isolation (250VAC/1min); Module-to-backplane optical isolation
Compatible Systems GE Mark VIe, Mark VI, Speedtronic series control systems
Communication Protocol Supports GE Proprietary Protocol, Modbus TCP, Ethernet/IP
Dimensions (L×W×H) 140mm × 85mm × 68mm
Weight Approximately 420g
Certification Standards UL, CSA, CE, IEC 61131-2, IEC 61010-1, RoHS
Mean Time Between Failures (MTBF) ＞180,000 hours
Diagnostic Functions Channel open-circuit detection, power failure alarm, overvoltage protection, signal drift monitoring

GE DS200CDBAG1ABA

Product Parameters

Parameter Name Specific Specifications
Brand & Model GE DS200CDBAG1ABA
Product Type Data Communication & Processing Module (for GE Mark VIe Control System)
Supported Communication Protocols GE Speedtronic, Ethernet/IP, MODBUS TCP, PROFINET IO
Communication Interfaces 2 x 10/100/1000M adaptive Ethernet ports (RJ45), 1 x dedicated GE controller bus interface
Data Transmission Rate Up to 1000 Mbps (Gigabit Ethernet), 100 Mbps (controller bus)
Communication Distance 100m for Ethernet (Cat5e/Cat6 cable); 50m for controller bus
Operating Voltage Range 20.4V DC – 28.8V DC
Operating Temperature Range -40°C – +70°C
Storage Temperature Range -40°C – +85°C
Protection Class IP20 (module body)
Mounting Method 35mm DIN rail mounting
Compatible Control Systems GE Mark VIe, Mark VI, and select Mark V control systems
Dimensions (L×W×H) 135mm × 155mm × 65mm
Weight Approximately 0.58kg
Protection Functions ESD protection (±25kV contact discharge), overvoltage protection, short-circuit protection, network overload protection
Status Indicators Power indicator, Ethernet link indicator, data transmit/receive indicator, controller bus status indicator, fault alarm indicator
Diagnostic Functions Built-in network fault self-diagnosis, protocol error logging, connection status monitoring

GE DS200ADGIH1AAA

¥12,999.00

Product Parameters

Parameter Name Specific Specifications
Brand & Model GE DS200ADGIH1AAA
Product Type Digital I/O Hybrid Module (for GE Mark VIe Control System)
Input Channel Count 16 digital input channels
Output Channel Count 16 digital output channels
Input Signal Type 24V DC dry contact/wet contact, sinking input (NPN)
Output Signal Type 24V DC sourcing output (PNP), configurable for high-side switching
Single-Channel Output Current Maximum 2A per output channel
Total Output Current ≤15A (sum of all output channels)
Input Response Time ≤1ms
Output Response Time ≤2ms
Operating Voltage Range 20.4V DC – 28.8V DC
Operating Temperature Range -40°C – +70°C
Storage Temperature Range -40°C – +85°C
Protection Class IP20 (module body)
Mounting Method 35mm DIN rail mounting
Compatible Control Systems GE Mark VIe, Mark VI, and selected Series 90-70 PLCs
Dimensions (L×W×H) 140mm × 155mm × 68mm
Weight Approximately 0.6kg
Protection Functions Overcurrent protection, short-circuit protection, reverse polarity protection, ESD protection (±25kV contact discharge)
Status Indicators Power indicator, input channel activity indicators, output channel activity indicators, fault alarm indicator
Diagnostic Functions Built-in channel fault self-diagnosis, overcurrent/short-circuit alarm logging

GE IC693ALG392B

¥25,899.00

Product Parameters

Parameter Name Specific Specifications
Brand & Model GE IC693ALG392B
Product Type Analog Input Module (for GE Series 90-30 PLC)
Input Channels 8 differential input channels
Supported Signal Types 4-20mA DC, 0-20mA DC, 0-10V DC, ±10V DC; compatible with thermocouples (J/K/T/E/R/S/B) and RTDs (PT100)
Input Accuracy ±0.1% Full Scale (FS) for current/voltage signals; ±0.2% FS for thermocouple/RTD signals
Signal Conversion Time ≤10ms per channel
Sampling Rate 50Hz per channel
Operating Voltage Range 120/240V AC (power supply module dependent)
Operating Temperature Range 0°C ~ 60°C
Storage Temperature Range -40°C ~ 85°C
Protection Class IP20 (module body)
Mounting Method DIN rail mounting (35mm standard rail)
Compatible PLC Series GE Series 90-30 PLC
Communication Interface GE Genius Bus protocol
Dimensions (L×W×H) 127mm × 89mm × 152mm
Weight Approximately 0.5kg
Protection Functions Overvoltage protection, reverse polarity protection, electrostatic discharge (ESD) protection (±15kV contact discharge)
Status Indicators Power indicator, channel activity indicators, system fault indicator

GE IC695PSD140

¥25,999.00

Key Technical Specifications

Parameter Category Detailed Specifications
Module Type Redundant AC-to-DC power supply module for GE RX3i PLC systems
Input Voltage Range 85–264V AC (50/60Hz, universal input for global compatibility)
Output Voltage & Current 24V DC (±0.5V regulation); 14A total output (7A per redundant PSU)
Redundancy Design 1+1 redundant PSUs; Automatic switchover (<1ms) if primary PSU fails
Protection Features Overload protection (150% of rated current), short-circuit protection, over-temperature shutdown
Efficiency ≥85% (at full load, 230V AC input)
Operating Temperature -20°C ~ +60°C (no derating required within range)
Protection Rating IP20 (panel-mounted in standard 19-inch control cabinets)
Form Factor DIN-rail mountable; Dimensions: 140mm (W) × 100mm (H) × 60mm (D)
Compatibility GE RX3i PLC systems (IC695CPU310/330), GE RX3i I/O modules (e.g., IC695IOL101), third-party 24V DC devices
Diagnostic Features LED indicators for PSU status (normal/fault), output voltage monitoring, fault logging
Sale!

GE IS200EPCTG1A

¥3,999.00

Product Parameters: Technical Specifications of GE IS200EPCTG1A

Parameter Category Specifications
Module Type 4-channel AI + 2-channel AO analog I/O module
AI Signal Compatibility 4–20mA DC (current), 0–10V DC (voltage); configurable per channel
AO Signal Output 4–20mA DC (sink/source), 0–10V DC; maximum load: 500Ω (current), 1kΩ (voltage)
Resolution 16-bit (AI/AO)
Accuracy ±0.1% of full scale (FS) at 25°C; ±0.2% FS over operating temperature range
Operating Temperature -40°C to +70°C (-40°F to +158°F)
Power Supply 24V DC (redundant input); typical power consumption: 3.5W
Isolation Channel-to-channel: 500V AC (galvanic); Module-to-ground: 1kV AC
Certifications IEC 61000-6-2 (EMC), UL 508 (industrial control), CSA C22.2 No. 142
Compatibility GE Mark VIe DCS; requires IS200EPDHG1B baseplate for mounting
Response Time <10ms (AI signal conversion); <5ms (AO command execution)

GE 516TX 336A4940DNP516TX

¥9,999.00

Technical Parameters

  • Device Type: Multifunctional protection relay for medium-voltage (3–35kV) power systems
  • Core Protection Functions:
    • Short-Circuit Protection: Three-stage overcurrent protection (instantaneous, time-delayed instantaneous, overcurrent) with adjustable setting range 0.5–20×CT rated current and operating time 0.01–10s
    • Overload Protection: Inverse-time or definite-time selectable, setting current 1.0–1.5×rated current, operating time 1–120s
    • Voltage Protection: Overvoltage protection (105–120% rated voltage), undervoltage protection (80–95% rated voltage), operating time 0.1–10s
    • Additional Protection: Phase-failure protection, earth fault protection, CT open-circuit detection, overtemperature protection (optional)
  • Measurement Parameters:
    • Current Measurement: Configurable CT ratio 1–2000:5A, accuracy ±0.2%FS
    • Voltage Measurement: Configurable VT ratio 100–10000:100V, accuracy ±0.2%FS
    • Power Measurement: Active power, reactive power, apparent power, accuracy ±0.5%FS
    • Frequency Measurement: 45–65Hz, accuracy ±0.01Hz
  • Communication & Control:
    • Communication Interfaces: RS-485 (supports Modbus RTU), Ethernet (supports Modbus TCP, DNP3.0 protocols)
    • Control Outputs: 4 groups of programmable relay outputs (NO/NC selectable), rated load AC 250V/5A, DC 30V/3A
    • Signal Inputs: 8 digital inputs (for external interlock signal access)
  • Power Supply & Power Consumption:
    • Supply Voltage: AC/DC 110–240V (wide voltage adaptation), power consumption ≤15W
  • Environmental & Mechanical Specifications:
    • Operating Temperature: -40℃~+70℃ (operation), -40℃~+85℃ (storage)
    • Protection Class: IP54 (suitable for outdoor distribution cabinets or harsh indoor environments)
    • Mounting Type: Panel mounting/rail mounting optional
    • Dimensions: 144mm (width) × 144mm (height) × 120mm (depth)
    • Weight: Approximately 1.8kg
  • Certifications & Standards:
    • Complies with IEC 61850, IEC 60255, UL 508, CE and other international standards
    • Protection Setting Storage: Non-volatile memory, data retention ≥10 years after power-off

GE DS200DCFBG2BNC MRP420024

¥9,999.00

Product Parameters

  • Component Type: Industrial DC-DC power supply module, dedicated to powering GE Speedtronic Mark VI/VII turbine control system electronics.
  • Input Specifications: DC input voltage range 18–32 V DC (nominal 24 V DC), compatible with GE’s redundant power supply systems; input current ≤ 10 A (full load).
  • Output Specifications: Dual isolated output channels; Channel 1: 5 V DC, 4 A (continuous), 6 A (peak, ≤ 3 seconds); Channel 2: 15 V DC, 2 A (continuous), 3 A (peak, ≤ 3 seconds); output voltage regulation ±0.1% (line regulation), ±0.2% (load regulation).
  • Isolation Performance: Input-output isolation voltage 2500 V AC (1 minute); inter-channel isolation voltage 1500 V AC (1 minute); insulation resistance ≥ 100 MΩ at 500 V DC, ensuring protection against voltage transients and cross-channel interference.
  • Ripple and Noise: ≤ 50 mVpp (Channel 1, 5 V DC); ≤ 100 mVpp (Channel 2, 15 V DC), minimizing interference with sensitive control electronics (e.g., analog signal converters).
  • Protection Functions: Overload protection (auto-recovery after fault clearance), short-circuit protection (current limiting), over-voltage protection (clamping at 110% of nominal output), over-temperature protection (auto-shutdown at ≥ 85°C), and reverse-polarity protection (input terminal).
  • Operating Environment: Temperature range -20°C to +70°C (operating); -40°C to +85°C (storage); relative humidity 5%–95% (non-condensing); vibration resistance up to 5 g (10–500 Hz); shock resistance up to 20 g (half-sine pulse, 11 ms duration).
  • Mechanical Specifications: Metal housing with IP20 protection rating; DIN rail or panel mounting; dimensions (W×D×H) 120 mm × 180 mm × 60 mm; weight ≈ 0.8 kg.
  • Compatibility: Fully compatible with GE Speedtronic Mark VI, Mark VIe, and Mark VII turbine control systems; compatible with GE DS200 series I/O modules, IS200 series excitation controllers, and Turbine Control Panels (TCPs).
  • Diagnostic Features: LED indicators for power status (green: normal; red: fault), output current monitoring, and over-temperature alerts; diagnostic data accessible via GE’s ToolboxST software for remote troubleshooting.
  • Compliance Standards: IEC 61000-6-2 (EMC immunity), IEC 61000-6-4 (EMC emissions), UL 508 (industrial safety), CE marking, and GE’s internal turbine control system certification (Mark VI/VII compliant).

GE IS220PPRFH1A

¥23,999.00

Technical Specifications

  • Device Type: Industrial PID control module for GE Mark VIe control systems
  • Control Function: Proportional-Integral-Derivative (PID) control; supports cascade control and feedforward control
  • Input Channels: 4 analog input channels (4–20 mA DC, 16-bit resolution) for sensor feedback
  • Output Channels: 2 analog output channels (4–20 mA DC, 16-bit resolution) for actuator control
  • Processing Speed: PID loop update rate ≤ 10 ms (ensures real-time response to process changes)
  • Control Accuracy: ±0.1% of full scale (FS) for both input sampling and output signals
  • Operating Environment: Temperature range 0°C to +60°C; humidity 5%–95% (non-condensing)
  • Power Supply: 24 V DC (redundant input design, voltage range 19.2 V–28.8 V); power consumption ≤ 6 W
  • Dimensions: 90 mm × 120 mm × 35 mm (L × W × H); compatible with GE Mark VIe standard racks
  • Protection Rating: IP20 (suitable for cabinet-mounted installation in control rooms)
  • Mounting Method: Slot-mounted in GE Mark VIe control racks (no additional brackets required)
  • Additional Features: Built-in loop tuning tools, fault diagnostics (via GE CIMPLICITY software), over-range/under-range protection, and Modbus TCP communication for remote monitoring