1.Parameters:
–Interfaces: Supports up to 8 different high-speed CAN bus interfaces1
–Data Transmission Rate: High-speed data transmission for real-time performance1
–Power Requirements: +3.3 VDC, +5 VDC, +12 VDC, -12 VDC1
2.Specifications:
–Compatibility: PCI Express interface card, compatible with NI PXI systems1
–Communication Protocols: Supports multiple CAN communication protocols1
–Operating Temperature Range: Not specifically mentioned, but typical industrial ranges apply2
3.Dimensions & Weight:
–Dimensions: Approximately 100mm x 50mm x 20mm
–Compatibility: Designed to work with SCXI and PXI/SCXI chassis systems from NI1
–Connection Capability: Provides from 6 to 32 circuits for connecting input and output devices1
Specifications:
–Brand: National Instruments (NI)
–Model: SCXI-1313A
–Type: Data Acquisition and Signal Conditioning Terminal Block
–Communication: Integrated communications capability with a microprocessor1
Dimensions & Weight:
–Dimensions: Approximately 22.5 x 10 x 7.5 cm (9 x 4 x 3 inches)1
–Weight: Approximately 1.8 kg (4 pounds)1
Synchronization Capabilities: Supports synchronization of PXI and PXI Express systems using GPS, IEEE 1588, IRIG-B, and PPS12
Timing Functions: Generates events and clock signals at synchronized time points, time-stamps input events based on synchronized system time12
3.Dimensions & Weight:
Exact dimensions and weight are not specified in the available information. However, it is a PXI module, so it adheres to the standard PXI form factor and weight limitations.
4.Series:
Part of NI’s PXI timing and synchronization module series.
Processor: 2.3GHz quad-core Intel Core i7-3610QE processor (Max 3.3GHz in single-core Turbo Boost mode)
Memory: 4 GB (1 x 4 GB DIMMs) dual-channel 1,600 MHz DDR3 RAM is standard, expandable up to 16 GB
System bandwidth: up to 8 GB/s, some say 2 GB/s, which may depend on the specific configuration or version
Slot bandwidth: 4 GB/s in standard configuration, some say 2 GB/s
specification
Type: PXI Express controller module
Manufacturer: National Instruments (NI)
Software support: Compatible with LabVIEW, LabVIEW Real-Time and other NI software platforms
Size and weight
Dimensions: 115mm x 48mm x 150mm
Weight: About 1.2kg
Parameters and specifications
Model: SCXI-1193
Manufacturer: National Instruments (NI)
Part number: 776572-93
Number of channels: 32
Frequency range: DC to over 500MHz
Scan rate: maximum 100 operations/second
Relay life: mechanical life of 50 million cycles, electrical life of 300,000 cycles (30V 0.3A DC resistance)
Trigger characteristics: Input trigger comes from SCXI trigger line 0 to 7, front panel, rear connector; Minimum pulse width 150 nanoseconds; The output trigger destination is SCXI trigger line 0 to 7, front panel, rear connector; Programmable pulse width (1μs to 62μs)
Physical properties: the type of relay is electromechanical latching relay; Contact materials are silver, palladium and gold
Size and weight
Dimensions: 1.2 x 6.8 x 7.8 inches (or 3.0 x 17.3 x 19.8 cm)
Weight: 2 ounces
argument
Number of channels: 16 channels
Resolution: 24 bits
Sampling rate: up to 100 MS/s
Input range: ±10V
Input impedance: 100kΩ
Trigger mode: software trigger, hardware trigger
Data transmission mode: DMA
specification
Processor: i.MX 6ULL processor based on NXP
Memory and Cache: Equipped with a variety of high-performance processing units, caches, and memory
I/O interfaces and communication interfaces: Rich interfaces for easy connection of various sensors, actuators and other devices
Supported data encryption protocols: A variety of data encryption protocols ensure the security and integrity of data during collection and transmission
Supported communication methods: Fieldbus, CANopen, Profibus, Ethercat, etc
Size and weight
Dimensions: 170mm x 105mm x 32mm
argument
Processor: 2.6GHz or 2.7GHz dual-core or 2.6GHz quad-core Intel Core i7 5700EQ processor
Memory: 4GB single-channel 1600 MHz DDR3L RAM is standard, expandable up to 8GB
Storage: Integrated hard drive, capacity may vary depending on configuration (e.g. 500GB)
System bandwidth: up to 8 GB/s
Slot bandwidth: 4 GB/s
specification
Type: PXI Embedded controller
Manufacturer: National Instruments (NI)
Operating system: Factory installation Win10(64-bit) and drivers
Size and weight
Dimensions: 115mm x 48mm x 150mm
Weight: Approx. 1.2kg (another saying is 2KG, may vary depending on configuration or version)
series
The PXIE-8840 is part of NI’s PXI family of controllers
Parameters and specifications
Data exchange capability: Up to 10,000 16-bit registers can be used to exchange large amounts of data.
Server connection: Supports three types of server connection, the number of which is 5.
Supported PLC types: PLC2, PLC5, SLC, CLX, CMPLX, MICROLX, etc.
Supported message types: PCCC and CIP.
Client connection: Of the three types of client connections, two are connected and one is not connected.
I/O connections: The number is 2 and the I/O connection size is 248/248.
Maximum RPI time: 5 milliseconds per connection.
Supported CIP services: including 0x4C-CIP data table reading.
Power supply: 24 VDC nominal, allowing range 10 to 36 VDC, allowing positive, negative, GND terminals.
Current load: 24 VDC nominal @ 300 mA, 10 to 36 volts DC at 610 mah Max.
Size and weight
Dimensions: 5.38 x 1.99 x 4.38 inches (or 13.67 x 5.05 x 11.13 cm).
Analog input: 8-way differential or 16-way single-ended.
Analog output: 4.
Digital I/O: 48 lines.
Update rate: Up to 1.25 MS/s.
Resolution: 16 bits.
Voltage range: ±10v, ±1v, ±100mv.
specification
Operating temperature: -20 ° C to 55 ° C in some descriptions, while 32 ° C to 90 ° C in others. It depends on the application scenario and product configuration.
Power consumption: 14w Max.
Software support: NI LabVIEW, NI-DAQMX.
Size and weight
Size: 13.4 x 5.0 inches (from search results 3), but there is also information that mentions the outline size of 10.6CM x 9.3CM x 2.3CM (product dimensions may not include frames or connectors, etc.).
