Description
Product Parameters
| Parameter | Specification |
|---|---|
| Brand / Series | GE Mark VIe Speedtronic |
| Model | IS200TSVCH1A |
| Servo Valve Channels | 4 independent channels |
| Command Output | ±10 VDC (programmable per channel, 16-bit DAC) |
| Output Current | ±20 mA (short-circuit protected) |
| Position Feedback Inputs | 4 channels (0–10 V, ±10 V, or 4–20 mA selectable) |
| Feedback ADC Resolution | 16-bit SAR (10–500 SPS) |
| Feedback Accuracy | ±0.1% FS |
| Diagnostics | Command output open/short detection, feedback open-circuit detection, feedback over/under-range monitoring |
| Status Indication | 4 green LEDs (command active), 4 red LEDs (fault per channel), 2 red summary fault LEDs |
| Isolation | 1500 VAC (field-to-system) |
| Operating Temperature | –30°C to +65°C |
| Storage Temperature | –55°C to +85°C |
| Mounting | VME rack-mount terminal board with front-panel I/O connectors |
| Backplane Interface | VME64x (A24/A32, D16/D32/D64) |
| EMC Compliance | IEC 61000-4 Level 4 |
Advantages & Key Features
-
High Channel Density: 4 independent servo valve channels in a single VME slot.
-
High-Resolution Command Output: 16-bit DAC provides precise servo valve control.
-
Integrated Position Feedback: Each channel includes dedicated feedback input for closed-loop position control.
-
Versatile Feedback Inputs: Supports 0–10 V, ±10 V, or 4–20 mA feedback signals.
-
Comprehensive Diagnostics: Command output open/short, feedback open-circuit, and over/under-range detection per channel.
-
Short-Circuit Protection: Outputs protected against short circuits.
-
Opto-Isolation: 1500 VAC isolation protects the Mark VIe backplane.
-
ToolboxST Integration: Full configuration, monitoring, and diagnostics via GE ToolboxST.
-
Drop-In Replacement: Direct replacement for earlier GE servo valve terminal boards.
Application Fields
-
Gas & Steam Turbines (GE Frame 6B/7EA/9E/HA): Fuel gas servo valve control, steam admission valve control, inlet guide vane (IGV) position control.
-
Combined Cycle Plants: Steam turbine valve position control.
-
Aeroderivative Turbines: Fuel control and IGV positioning.
-
Compressor Stations: Anti-surge valve control.
Comparison with Competing Products
| Feature | GE IS200TSVCH1A | Competitor A (Servo Valve Module) | Competitor B (Analog Output Module) |
|---|---|---|---|
| Channels | 4 | 2 | 4 |
| Command Resolution | 16-bit | 14-bit | 16-bit |
| Feedback Inputs | Yes (4) | No | No |
| Diagnostics | Command open/short, feedback open/over/under | Command only | Output only |
| Isolation | 1500 VAC | 1000 VAC | 500 VDC |
| Operating Temp | –30°C to +65°C | 0°C to 50°C | 0°C to 60°C |
Key Advantage: IS200TSVCH1A provides 4 servo valve channels with integrated position feedback, 16-bit command resolution, and comprehensive diagnostics—double the density of competing modules and ideal for turbine servo valve control.
Selection Guidelines & Recommendations
-
Channel Count: Up to 4 servo valves per board.
-
Command Output: Configure ±10 VDC command output in GE ToolboxST.
-
Feedback Type: Select feedback input type (0–10 V, ±10 V, or 4–20 mA) per channel.
-
Controller Firmware: Requires Mark VIe processor firmware v7.5 or later.
-
Wiring Guidelines: Use shielded twisted-pair cables for command and feedback signals.
-
Spare Strategy: Keep one spare per turbine; lead times 6–8 weeks.
-
Retrofit: Direct replacement—regenerate configuration in GE ToolboxST.
Important Cautions
-
No Hot-Swap: De-energize rack before insertion/removal.
-
Output Short: Command outputs are short-circuit protected but sustained shorts may cause thermal shutdown.
-
Feedback Polarity: Observe correct polarity for feedback connections.
-
Grounding: Connect AGND to Mark VIe system ground at single star point.
-
Shield Termination: Ground signal cable shields only at cabinet end.
-
ESD Handling: Use grounded wrist straps; field repair not possible.
-
Channel Mapping: Verify field wiring maps to correct ToolboxST channel numbers.
TRICONEX AI2351
GE IC695CHS012
Whitman Controls W117V-3H-F52M-X
Reviews
There are no reviews yet.