Description
Product Parameters
| Parameter | Specification |
|---|---|
| Brand / Series | GE Mark VIe Speedtronic |
| Model | IS200TBAOH1CCB |
| Analog Outputs | 32 channels (4–20 mA or 0–10 V, software-selectable per channel) |
| Output Range | 0–20 mA, 4–20 mA, 0–5 V, 0–10 V |
| DAC Resolution | 16-bit with programmable update rate (1–1000 SPS) |
| Accuracy | ±0.05% of full scale (25°C), ±0.1% over full temperature range — upgraded from ±0.1% / ±0.2% |
| Load Impedance | 0–750 Ω (current mode), > 2 kΩ (voltage mode) |
| Current Limit | 25 mA per channel (short-circuit protected) |
| Filtering | Programmable low-pass filter (1–50 Hz) with enhanced anti-aliasing |
| Isolation | 2000 VAC (field-to-system) — upgraded from 1500 VAC |
| Diagnostics | Open-circuit detection, short-circuit detection, over/under-range monitoring, reference voltage self-validation |
| Status Indication | 32 green LEDs (channel active), 2 red LEDs (diagnostic fault summary), 1 yellow LED (reference status) |
| Operating Temperature | –40°C to +70°C — upgraded from –30°C to +65°C |
| Storage Temperature | –55°C to +85°C |
| Mounting | VME rack-mount terminal board with front-panel I/O connector |
| Backplane Interface | VME64x (A24/A32, D16/D32/D64) |
| EMC Compliance | IEC 61000-4 Level 4 |
Advantages & Key Features
-
Maximum Channel Density: 32 analog outputs in a single VME slot—double the density of IS200TBAOH1B (24 channels) and four times that of competing 8-channel modules.
-
Superior Accuracy: ±0.05% full-scale accuracy provides higher precision for critical turbine actuator control.
-
Extended Temperature Range: –40°C to +70°C operation makes IS200TBAOH1CCB suitable for arctic, desert, and unheated turbine enclosures.
-
Enhanced Isolation: 2000 VAC isolation provides superior protection for the Mark VIe backplane from field wiring faults and surges.
-
Flexible Output Configuration: Each channel supports 4–20 mA or 0–10 V outputs via GE ToolboxST.
-
High Resolution: 16-bit DAC provides precise control for critical turbine parameters.
-
Programmable Filtering: Onboard low-pass filter (1–50 Hz) smooths output signals to reduce mechanical wear on actuators.
-
Comprehensive Diagnostics: Open-circuit, short-circuit, over/under-range, and reference self-validation per channel.
-
Short-Circuit Protection: Each output is protected against short circuits and overcurrent conditions.
-
ToolboxST Integration: Full configuration, calibration, and diagnostics via GE ToolboxST.
-
Drop-In Replacement: Direct replacement for IS200TBAOH1C and earlier analog output terminal boards.
Application Fields
-
Gas & Steam Turbines (GE Frame 6B/7EA/9E/HA): Fuel gas control valves, steam admission valves, inlet guide vane positioners, bypass valves, actuator position control, variable speed drive control, auxiliary system actuators, generator cooling control.
-
Combined Cycle Plants: HRSG feedwater control valves, bypass valve positioning, steam temperature control actuators, condensate control.
-
Compressor Stations: Anti-surge valve control, recycle valve positioning, variable speed compressor control, blow-down valve control.
-
Arctic & Desert Installations: Extreme-environment turbine control cabinets.
-
Offshore Platforms: Marine enclosures with salt-spray and wide temperature swings.
-
Aeroderivative Turbines: Fuel control actuators, variable inlet guide vanes, bleed valve control, oil temperature control.
Comparison with Competing Products
| Feature | GE IS200TBAOH1CCB | GE IS200TBAOH1C | Competitor A (Emerson) | Competitor B (Siemens) |
|---|---|---|---|---|
| Analog Outputs | 32 | 32 | 8 | 8 |
| Accuracy | ±0.05% FS | ±0.1% FS | ±0.2% FS | ±0.15% FS |
| Isolation | 2000 VAC | 1500 VAC | 1000 VAC | 500 VDC |
| Operating Temp | –40°C to +70°C | –30°C to +65°C | 0°C to 50°C | 0°C to 60°C |
| Reference Self-Validation | Yes | No | No | No |
| EMC Filtering | IEC Level 4 | Level 2 | Level 2 | Level 1 |
Key Advantage: IS200TBAOH1CCB delivers 32 analog outputs with ±0.05% accuracy, extended –40°C to +70°C temperature range, 2000 VAC isolation, and reference self-validation—making it the premier analog output terminal board for extreme-environment, high-channel-count turbine actuator control applications.
Selection Guidelines & Recommendations
-
Output Type: Configure 4–20 mA or 0–10 V per channel in GE ToolboxST.
-
Load Verification: Ensure connected actuators do not exceed load impedance capability (0–750 Ω for current, > 2 kΩ for voltage).
-
Filtering: Use 1–10 Hz for smooth actuator response, 20–50 Hz for faster dynamic control.
-
Controller Firmware: Requires Mark VIe processor firmware v8.0 or later.
-
Spare Strategy: Keep one spare per turbine; lead times 8–12 weeks.
-
Retrofit: Direct replacement for IS200TBAOH1C—regenerate configuration in GE ToolboxST to access enhanced features.
Important Cautions
-
No Hot-Swap: De-energize rack before insertion/removal.
-
Output Polarity: Observe correct polarity for current loops.
-
Short-Circuit Protection: While protected, sustained short circuits may cause thermal shutdown. Investigate wiring faults promptly.
-
Grounding: Connect AGND to Mark VIe system ground at single star point.
-
Shield Termination: Ground output cable shields only at cabinet end.
-
ESD Handling: Use grounded wrist straps; field repair not possible.
-
Filtering Trade-Off: Higher filtering provides smoother output but introduces signal delay—balance based on actuator response requirements.
-
Channel Mapping: With 32 channels, verify wiring maps to correct ToolboxST channel assignments.
-
Power Supply: Ensure rack power supply provides adequate current for all active outputs (20 mA × 32 channels = 640 mA max).
-
Temperature Rating: Verify cabinet ambient does not exceed +70°C or fall below –40°C.
-
Reference Validation: Yellow LED indicates reference drift—schedule factory recalibration if illuminated.
SIEMENS 6GK1502-2CB10
PHOENIX IB STME 230 DI 16/3 2721125
GE 8913-PS-AC
Reviews
There are no reviews yet.