GE IS2020RKPSG1AG

Key Specifications

Advantages & Distinctive Features

• Ruggedized Design: Engineered for extreme high-vibration and shock environments.

• Enhanced Surge Suppression: ±4 kV surge withstand protects against lightning-induced surges.

• Widest Temperature Range: –40 °C to +85 °C—suitable for the most extreme environments.

• Thickest Silicone Conformal Coating + Edge Encapsulation: Maximum protection against humidity, salt spray, chemicals, and condensing environments.

• Condensing Humidity Rating: 5–100% condensing—suitable for offshore and unheated installations.

• Expanded Diagnostic Log: 1000-event log with voltage/current waveforms for comprehensive post-event analysis.

• Military-Grade Manufacturing: 168-hour burn-in, 100% X-ray/AOI, military-grade components, 150 thermal cycles (–40 to +105 °C)—maximum field reliability.

• Gold-Plated Captive Washer Terminals: Corrosion-resistant and vibration-proof connections.

• Hot-Swappable: No rack power-down for replacement.

• Direct Retrofit: Replaces all RKPSG, LVPSG, and VPWR series boards.

Application Fields

• Turbine Control Racks: Primary power source for Mark VIe racks in extreme environments

• Nuclear Power Plants: Safety-critical power applications with highest reliability

• Military/Marine Applications: High-vibration, extreme temperature, and salt-spray environments

• Offshore Platforms: Salt-spray and condensing environments

• Arctic Installations: Extreme cold (–40 °C) environments

• Desert Power Plants: Extreme heat (+85 °C) environments

• Chemical Processing: Corrosive environments

• Retrofit Projects: Upgrading older power supplies in the most demanding applications

Comparison with RKPSG1AD and Competitors

The GE IS2020RKPSG1AG offers the same ruggedized 200 W capacity as the RKPSG1AD variant but with widest temperature range, enhanced thermal cycling, longest burn-in, and highest-quality manufacturing—making it the ultimate power supply solution for critical applications in the world’s most extreme environments.

Selection Guidelines

• When to choose:

  • Extreme environments (–40 to +85 °C, condensing, chemical exposure, salt spray)

  • Maximum reliability applications (nuclear, military, critical infrastructure)

  • High-vibration applications (marine, compressor stations, turbine decks)

  • Lightning-prone installations requiring enhanced surge suppression

• When to choose RKPSG1AD instead: For less extreme environments (–40 to +80 °C) where standard military-grade manufacturing suffices.

• Load Calculation: Sum all board loads—ensure total ≤200 W. +5 V rail ≤25 A; +3.3 V rail ≤20 A.

• Redundancy Planning: For critical turbines, order two GE IS2020RKPSG1AG units with diode-OR configuration.

• Input Wiring: Use 12 AWG minimum; install fast-acting fuse (25 A) or circuit breaker.

• Cooling: Ensure cabinet airflow ≥150 LFM; derate above 75 °C.

• Coating Verification: Inspect under UV (365 nm)—thickest silicone coating shows distinct fluorescence; verify edge encapsulation bead is continuous and visibly thickest.

• Compatibility: Fits all Mark VIe VME64x racks. Requires ControlST v6.5 or higher.

Operational Precautions

1. Input Polarity: Double-check DC input polarity before power-up.

2. Load Calculation: Verify total rack load ≤200 W. Overloading +5 V rail (25 A max) is a common error—measure current draw during commissioning.

3. Vibration Mounting: In high-vibration installations, verify cabinet and module mounting are properly secured to prevent connector stress.

4. Status Monitoring: Regularly check front-panel LEDs—if any rail LED is amber/red, investigate downstream load.

5. Redundancy Testing: For redundant configurations, perform manual failover tests during outages.

6. Fault Log: Access 1000-event log via Toolbox ST—review voltage/current waveforms for post-event analysis.

7. Coating Care: Use GE-approved silicone-safe cleaner; inspect annually under UV—rework voids with approved silicone coating per GE FSB-MKVIe-112.

8. Hot-Swap: Remove/insert slowly under power—processor auto-recognizes new module.

9. Spare Stock: Maintain 1 spare per 3–4 racks; “RKPSG1AG” backward-compatible with all RKPSG/LVPSG/VPWR sockets.

10. Firmware Updates: Ensure the GE IS2020RKPSG1AG is in “standby” mode during updates.

11. Thermal Derating: Above 75 °C, reduce load to 170 W max—monitor via I/O Net telemetry.

12. ESD: Handle by edges only with grounded wrist strap—coating does not protect connectors.

13. Storage: Anti-static bag with desiccant at –40 to +85 °C; rotate every 3 years for coating inspection.