Description
Product Parameters
| Parameter | Specification |
|---|---|
| Brand / Series | GE Mark VIe Speedtronic |
| Model | IS200TBAIH1A |
| Analog Inputs | 16 channels (4–20 mA, 0–10 V, ±10 V selectable) |
| ADC Resolution | 16-bit SAR with programmable sampling rate (10–500 SPS) |
| Accuracy | ±0.1% of full scale (25°C), ±0.2% over full temperature range |
| Loop Power | 24 VDC (externally supplied only — no internal loop power) |
| Input Impedance | 250 Ω (current mode), > 1 MΩ (voltage mode) |
| Filtering | Programmable low-pass filter (1–50 Hz) |
| Isolation | 1500 VAC (field-to-system) |
| CMRR | >100 dB @ 50/60 Hz |
| Diagnostics | Open-circuit detection, over-range/under-range detection, loop power fault monitoring |
| Status Indication | 16 green LEDs (channel active), 2 red LEDs (diagnostic fault summary) |
| Operating Temperature | –30°C to +65°C |
| Storage Temperature | –55°C to +85°C |
| Mounting | VME rack-mount terminal board with front-panel I/O connector |
| Backplane Interface | VME64x (A24/A32, D16/D32/D64) |
Advantages & Key Features
-
High Channel Density: 16 analog inputs in a single VME slot, suitable for turbines with extensive pressure, temperature, and flow monitoring.
-
Flexible Input Configuration: Each channel supports 4–20 mA, 0–10 V, or ±10 V inputs via GE ToolboxST software.
-
Programmable Filtering: Onboard low-pass filter (1–50 Hz) optimizes noise rejection vs. response speed.
-
Comprehensive Diagnostics: Real-time open-circuit, over-range/under-range, and loop power fault monitoring per channel.
-
Wide Input Compatibility: Accommodates both current and voltage sensors without external signal conditioners.
-
ToolboxST Integration: Full configuration, calibration, and diagnostics via GE ToolboxST.
-
Drop-In Replacement: Direct replacement for earlier GE analog input terminal boards.
Application Fields
-
Gas & Steam Turbines (GE Frame 6B/7EA/9E/HA): Fuel gas pressure/flow, steam pressure/temperature, bearing vibration (via transmitters), lube oil pressure/temperature, cooling water pressure, valve position feedback.
-
Combined Cycle Plants: HRSG feedwater flow, steam drum pressure, superheater temperature, condensate flow.
-
Compressor Stations: Suction/discharge pressure, gas flow, vibration transducers, intercooler temperature.
-
Aeroderivative Turbines: Fuel flow, engine oil pressure, inlet guide vane position, exhaust temperature transmitters.
Comparison with Competing Products
| Feature | GE IS200TBAIH1A | Competitor A (Emerson Analog) | Competitor B (Siemens Analog) |
|---|---|---|---|
| Analog Inputs | 16 | 8 | 8 |
| Input Types | 4–20 mA, 0–10 V, ±10 V | 4–20 mA only | 4–20 mA, 0–10 V |
| Accuracy | ±0.1% FS | ±0.2% FS | ±0.15% FS |
| Isolation | 1500 VAC | 1000 VAC | 500 VDC |
| Operating Temp | –30°C to +65°C | 0°C to 50°C | 0°C to 60°C |
Key Advantage: IS200TBAIH1A provides double the channel density (16 vs. 8) of competing modules with flexible input configuration and comprehensive diagnostics—reducing rack space and simplifying system design.
Selection Guidelines & Recommendations
-
Input Type: Configure 4–20 mA, 0–10 V, or ±10 V per channel in GE ToolboxST.
-
Loop Power: External 24 VDC supplies required—plan cabinet power distribution accordingly.
-
Filtering: Use 1–10 Hz for temperature/pressure, 20–50 Hz for dynamic signals.
-
Controller Firmware: Requires Mark VIe processor firmware v6.5 or later.
-
Spare Strategy: Keep one spare per turbine; lead times 6–10 weeks.
-
Retrofit: Direct replacement—regenerate configuration in GE ToolboxST.
Important Cautions
-
No Hot-Swap: De-energize rack before insertion/removal.
-
External Loop Power Required: No internal loop power—ensure 24 VDC supplies are connected.
-
Input Overload: Sustained input >30 V or >50 mA may damage input circuitry.
-
Grounding: Connect AGND to Mark VIe system ground at single star point.
-
Shield Termination: Ground shields only at cabinet end.
-
ESD Handling: Use grounded wrist straps; field repair not possible.
-
Filtering Trade-Off: Lower cutoff = better noise rejection but more signal delay.
-
Channel Mapping: Verify wiring maps to correct ToolboxST channel assignments.
A-B 1756-IT6I2
ABB AO815
A-B 1794-IR8
ABB AI815
Reviews
There are no reviews yet.