GE DS3800NPIA

Key Technical Parameters

Advantages and Distinctive Features

• Solid-State-Primary Hybrid + Tachometer Feedback: 8 solid-state DC outputs (3A) + 4 high-current relays (5A) + 2 tachometer inputs on a single board.

• Dual Temperature Sensor Support (4 T/C + 8 RTD): 12 total channels—optimized for RTD-heavy applications with limited T/C requirements.

• Higher Solid-State Current (3A): Supports larger DC fans compared to 2A boards.

• Higher Relay Current (5A): Supports larger AC/DC auxiliary loads compared to 3A boards.

• RTD Fault Detection: Continuous monitoring for open-circuit, short-circuit, or lead-wire degradation.

• Fan-Dense Design: 8 SS outputs + 4 relay outputs with only 4 T/C + 8 RTD inputs.

• Silent, Maintenance-Free Solid-State Outputs: Unlimited cycle life for DC fans.

• Fan Speed Verification: Tachometer inputs allow CPU to confirm fan operation.

Typical Application Fields

• Safety-Critical Fan-Dense Mixed Fan Systems: Where redundant temperature sensing and fan failure detection are mandatory.

• RTD-Heavy Cabinets: Where RTD sensors are preferred over thermocouples.

• Mixed Fan Cabinets: Where larger DC fans and high-power AC/DC auxiliary devices coexist.

• Climate-Controlled Indoor Installations: 0°C to +60°C range.

Comparison with Related Models

Selection Recommendations

• Choose the DS3800NPIA if:

  • You need 8 solid-state DC outputs (3A) for larger main fans.

  • You also need 4 high-current mechanical relay outputs (5A) for auxiliary devices.

  • You require both thermocouple and RTD inputs (12 total channels).

  • You require RTD fault detection for sensor integrity monitoring.

  • You require tachometer feedback for fan speed verification.

  • You have a climate-controlled environment (0°C to +60°C).

• Choose the DS3800NPDA if: You need the same outputs without RTD inputs.

• Choose the DS3800NPCM if: You need 16 total temperature channels (8 T/C + 8 RTD) with the same outputs.

Critical Precautions

• ESD Protection: Always wear a grounded wrist strap.

• DC Polarity (SS): Solid-state outputs are DC-only and polarity-sensitive—reverse polarity destroys the MOSFET.

• SS Voltage Limit: Do not exceed 48VDC—AC voltages cause catastrophic failure.

• SS Current Limitation: Rated at 3A continuous. Verify fan current does not exceed this limit.

• High-Voltage/Current Hazard (Relay): Relay outputs switch 115VAC/5A—lethal. Use proper insulation.

• Relay Inductive Derating: For inductive loads, derate from 5A to 3.5A or use RC snubbers.

• RTD Wiring: Use 3-wire Pt100 RTDs. All three wires must be connected. Open/short circuits trigger RTD Fault LED.

• RTD Lead Resistance: Use wire with resistance ≤10Ω per lead for accurate measurements.

• Missing T/C Channels: Only 4 thermocouple inputs (channels 1–4). Channels 5–8 are physically absent.

• Tachometer Wiring: Use shielded twisted-pair cable. Connect shield to designated terminal—not at the fan end.

• No Hot-Swap: Always depower the rack before insertion/removal.

• Slot Assignment: Install in slots 8–10 (auxiliary I/O).

• CPU Dependency: If backplane communication is lost, the board defaults to 100% fan speed—tachometer monitoring and RTD fault detection disabled in fallback mode.

• Firmware Compatibility: The DS3800NPIA is compatible with Mark V CPU firmware v4.0 and above for full RTD support. For v3.x, RTD inputs may be partially disabled—confirm compatibility before purchasing.