Description
Key Technical Parameters
| Parameter | Specification |
|---|---|
| Manufacturer | General Electric (GE) |
| Series | Mark V (Speedtronic) |
| Full Model | DS3800NPCF1A1A |
| Power Supply | +5V DC @ 4.5A, +15V DC @ 0.8A, -15V DC @ 0.6A |
| Temperature Inputs | 8 thermocouple channels (12-bit ADC, ±2°C accuracy) |
| SS Outputs | 8 solid-state relays, 3A continuous @ 24–48VDC |
| Relay Outputs | 4 mechanical relays, 5A continuous @ 115VAC/30VDC (surge 10A) |
| Tachometer Inputs | 2 channels (up to 10 kHz) |
| Communication | Mark V proprietary parallel backplane bus |
| Operating Temperature | 0°C to +60°C |
| LED Indicators | Power, SS Run (8x green), Relay Run (4x amber), Tach Fail (red x2), Over-Temp Alarm, Backplane Active |
Advantages and Distinctive Features
-
Solid-State-Primary Hybrid + Tachometer Feedback: 8 solid-state DC outputs (3A) + 4 high-current relays (5A) + 2 tachometer inputs on a single board.
-
Full 8 Thermocouple Inputs: Comprehensive temperature monitoring.
-
Higher Solid-State Current (3A): Supports larger DC fans compared to 2A boards.
-
Higher Relay Current (5A): Supports larger AC/DC auxiliary loads.
-
Baseline Revision A: The original version of this board—ideal for direct replacement in legacy systems.
-
Silent, Maintenance-Free Solid-State Outputs: Unlimited cycle life for DC fans.
-
Relay Auxiliary Outputs: 2500V galvanic isolation for AC/DC auxiliary loads.
-
Fan Speed Verification: Tachometer inputs allow CPU to confirm fan operation.
-
Low EMI Emissions: Solid-state outputs minimize interference with sensitive cards.
Typical Application Fields
-
Safety-Critical Mixed Fan Systems: Where fan failure detection is mandatory.
-
Mixed Fan Cabinets: Where larger DC fans, high-power AC/DC auxiliary devices, and comprehensive temperature monitoring are required.
-
Climate-Controlled Indoor Installations: 0°C to +60°C range.
-
Legacy System Replacements: Direct drop-in replacement for original DS3800NPCF boards.
Comparison with Related Models
| Feature | DS3800NPCF1A1A | DS3800NPCF (Base) | DS3800NPCE1A1B | DS3800NOAB1C1B |
|---|---|---|---|---|
| SS Outputs | 8 × 3A | 8 × 3A | 8 × 3A | 8 × 2A |
| Relay Outputs | 4 × 5A | 4 × 5A | 4 × 5A | 4 × 3A |
| T/C Inputs | 8 | 8 | 4 | 8 |
| Tach Inputs | 2 channels | 2 channels | 2 channels | 2 channels |
| ADC Resolution | 12-bit (±2°C) | 12-bit (±2°C) | 12-bit (±2°C) | 16-bit (±1°C) |
| Operating Temp | 0°C to +60°C | 0°C to +60°C | -20°C to +65°C | -20°C to +65°C |
| Firmware | A | Unknown | A | C |
| Cost | Medium-High | Medium-High | Medium-High | Medium |
Selection Recommendations
-
Choose the DS3800NPCF1A1A if:
-
You need 8 solid-state DC outputs (3A) for larger main fans.
-
You also need 4 high-current mechanical relay outputs (5A) for auxiliary devices.
-
You require tachometer feedback for fan speed verification.
-
Your cabinet uses 8 temperature sensors for comprehensive monitoring.
-
You have a climate-controlled environment (0°C to +60°C).
-
You need a direct replacement for an existing DS3800NPCF board.
-
-
Choose the DS3800NPCE1A1B if: You need the same features but only require 4 thermocouple inputs with extended temperature range (-20°C to +65°C).
-
Choose the DS3800NOAB1C1B if: You need 2A solid-state outputs, 3A relay outputs, and improved accuracy with extended temperature range.
Critical Precautions
-
ESD Protection: Always wear a grounded wrist strap.
-
DC Polarity (SS): Solid-state outputs are DC-only and polarity-sensitive—reverse polarity destroys the MOSFET.
-
SS Voltage Limit: Do not exceed 48VDC—AC voltages cause catastrophic failure.
-
SS Current Limitation: Rated at 3A continuous. Verify fan current does not exceed this limit.
-
High-Voltage/Current Hazard (Relay): Relay outputs switch 115VAC/5A—lethal. Use proper insulation.
-
Relay Inductive Derating: For inductive loads, derate from 5A to 3.5A or use RC snubbers.
-
Tachometer Wiring: Use shielded twisted-pair cable. Connect shield to designated terminal—not at the fan end.
-
No Hot-Swap: Always depower the rack before insertion/removal.
-
Slot Assignment: Install in slots 8–10 (auxiliary I/O).
-
CPU Dependency: If backplane communication is lost, the board defaults to 100% fan speed—tachometer monitoring disabled in fallback mode.
-
Firmware Compatibility: The DS3800NPCF1A1A is compatible with all Mark V CPU firmware versions (v3.x and above). No specific CPU upgrade is needed.
ABB 3HAC16831-1
siemens A5E39696191
A-B 1756-BA2
Reviews
There are no reviews yet.