GE DS3800NHVN

Key Technical Parameters

Advantages and Distinctive Features

• Highest Relay Current (4A @ 125VDC): Delivers 4A continuous (8A surge)—the highest current capacity of any high-voltage DC fan board in the Mark V lineup, supporting the largest 125VDC exhaust fans.

• Highest Solid-State Outputs (4A): The highest current rating for solid-state auxiliaries in the high-voltage lineup, with individual current monitoring and overcurrent detection.

• Full 16 Temperature Channels (8 T/C + 8 RTD): Comprehensive temperature monitoring without compromise.

• Predictive Thermal Modeling: Learns cabinet thermal response during 24-hour initial period, reducing temperature overshoot by up to 50%.

• 24-Bit Ultra-High Precision ADC: ±0.5°C for thermocouples, ±0.3°C for RTDs.

• Predictive Relay Maintenance: Real-time contact resistance monitoring with relay degradation warning.

• Hybrid Output + Tachometer Feedback: Combines 8 high-voltage DC relay outputs, 4 high-current solid-state outputs, AND 2 tachometer inputs.

• RTD Fault Detection: Continuous monitoring for open-circuit, short-circuit, or lead-wire degradation.

• Extended +85°C Operation: Surpasses the +75°C limit for extreme environments.

• 500-Event Fault Log: Comprehensive diagnostics.

Typical Application Fields

• High-Power 125VDC Cooling Systems: Where 4A @ 125VDC capacity is required for the largest exhaust fans.

• Mixed Sensor Cabinets: Where both thermocouple and RTD sensors are used (16 total channels).

• Extreme Desert Solar-Thermal Plants: +85°C ambient environments.

• Offshore Oil & Gas Platforms: Extreme temperature and vibration environments.

• Arctic Installations: -40°C low-temperature tolerance.

• Nuclear Auxiliary Turbines: High reliability with redundant temperature sensing and predictive maintenance.

• Large Auxiliary Fan Systems: Where 4A solid-state outputs are needed.

Comparison with Related Models

Selection Recommendations

• Choose the DS3800NHVN if:

  • You need the highest 125VDC relay current (4A) for the most powerful exhaust fans.

  • You need 4A solid-state outputs with individual current monitoring for larger auxiliary fans.

  • You require both thermocouple and RTD inputs (16 total channels).

  • You require tachometer feedback for fan speed verification.

  • You want predictive thermal modeling for proactive temperature management.

  • You want predictive relay maintenance .

  • You need 24-bit ADC accuracy.

  • Your installation operates in extreme heat up to +85°C with high vibration.

  • You need 500-event fault logging.

• Choose the DS3800NHVM1E1D if: You need 3A relay current with the same advanced features (4A SS, 16 channels, predictive modeling).

• Choose the DS3800NHVM1E1C if: You need 3A relay current and predictive modeling but only require 4 T/C + 8 RTD inputs (12 channels).

Critical Precautions

• ESD Protection: Always wear a grounded wrist strap. Static damage to the 24-bit ADC degrades accuracy.

• High-Voltage Hazard: Relay outputs switch 125VDC—lethal voltage present on terminals. Observe all high-voltage safety procedures. Use wiring rated for ≥125VDC.

• RTD Wiring: Use 3-wire Pt100 RTDs. All three wires must be connected. Open/short circuits trigger RTD Fault LED.

• RTD Lead Resistance: Use wire with resistance ≤10Ω per lead.

• DC Polarity (Relay): Relay outputs are DC only—observe correct polarity.

• DC Polarity (SS): Solid-state outputs are DC-only and polarity-sensitive—reverse polarity destroys the MOSFET.

• SS Overcurrent Protection: If an output exceeds 4.5A, the green LED flashes red. Persistent overcurrent triggers a bus fault and disables the output.

• SS Derating: At 85°C, derate to 3.0A per solid-state output.

• Tachometer Wiring: Use shielded twisted-pair cable. Connect shield to designated terminal.

• Relay Current Limitation: Rated at 4A continuous @ 125VDC. Verify fan current does not exceed this limit.

• Inductive Load Derating (Relay): For inductive fan motors, derate to 3A or use external RC snubbers (rated for 125VDC).

• Predictive Model Learning: Requires 24-hour initial learning period—do not interrupt power.

• Model Reset: Reset via Mark V software if cabinet configuration changes.

• No Hot-Swap: Always depower the rack before insertion/removal.

• Slot Assignment: Install in slots 8–10 (auxiliary I/O).

• CPU Dependency: If backplane communication is lost, the board defaults to 100% fan speed—all advanced features disabled in fallback mode.

• Firmware Compatibility: The DS3800NHVN requires Mark V CPU firmware v5.5 or higher for full predictive modeling, predictive maintenance, RTD support, 24-bit ADC, and SS current monitoring. For v5.0–v5.4, predictive modeling disabled. For v4.x, reverts to 16-bit mode.

• Power Supply: Draws 6.5A on +5V rail—the highest of any Mark V fan board. A power supply upgrade is mandatory for all installations.