DS3800HITA1F1F GE

Parameters

• Input Type: 4–20mA (default), 0–10V DC, ±10V DC (jumper-configurable)

• Channels: 4 differential (fixed)

• Resolution: 12-bit ADC

• Accuracy: ±0.075% of full scale (F1)

• Sampling Rate: Up to 1.5kHz per channel (F1 optimized)

• Scan Rate: 0.65ms per channel (F1 optimized)

• Input Impedance: 250Ω (current) / >1MΩ (voltage)

• Filtering: Programmable low-pass filter with adaptive anti-aliasing and real-time noise profiling (F1 feature)

• Isolation: 2500V RMS optical isolation (channel-to-backplane)

• Power: +5V DC @ 0.9A, +15V DC @ 0.25A (requires both rails)

• Data Buffering: Onboard FIFO buffer for burst data capture (F1 feature)

• Coating: Conformal coating (suffix F) – multi-layer acrylic with enhanced chemical and moisture resistance (superior to E)

• Temp Range: -18°C to +74°C (extended over E variant)

• Mounting: 6U VME Eurocard, single-slot

• Diagnostics: Enhanced onboard with per-channel LED status, signal noise detection, sampling integrity monitoring, buffer status, and calibration alerts (F1 feature)

Advantages & Features

• High-speed sampling (1.5kHz) captures fast-changing signals for real-time turbine protection with improved stability

• F1 firmware offers better accuracy (±0.075%), faster scan (0.65ms), adaptive anti-aliasing filtering, real-time noise profiling, onboard FIFO data buffering, and enhanced diagnostics

• Higher isolation (2500V) protects against ground loops and transient surges

• 4 differential channels provide noise rejection for high-speed signals in turbine environments

• Onboard FIFO buffer allows burst data capture for transient analysis and post-event diagnostics

• F-grade coating provides superior moisture and chemical resistance compared to E – suitable for environments with frequent humidity or chemical exposure

• Extended temperature range (-18°C to +74°C) offers more flexibility than E variant

• Front-panel LEDs for per-channel status including sampling integrity and buffer status alerts

• Compatible with Mark IV backplanes and some VIe systems (with adapter)

Application Cases

• Turbine shaft vibration monitoring – high-speed 4–20mA signals from proximity probes with burst data capture for transient analysis in chemically exposed environments

• Overspeed detection – dynamic speed signals requiring sub-0.7ms response times with real-time noise profiling

• Dynamic pressure monitoring – fast-changing combustion pressure signals with adaptive filtering and FIFO buffering

• Thrust position monitoring – high-speed LVDT feedback for axial position in plants with chemical exposure

• Retrofit projects upgrading from E1 firmware or lower-grade coatings for better performance and environmental protection

Competitor Comparison

• vs. DS3800HITA1F1E (F1/E variant): Superior moisture and chemical resistance (F vs. E), wider temp range (-18°C vs. -15°C, +74°C vs. +72°C) – otherwise identical specifications

• vs. DS3800HITA1E1E (E1/E variant): Better accuracy (±0.075% vs. ±0.08%), faster sampling (1.5kHz vs. 1.2kHz), faster scan (0.65ms vs. 0.8ms), F1 diagnostics, real-time noise profiling, onboard FIFO buffer, and superior F coating (vs. E) – significant upgrade

• vs. DS3800HITA (standard A variant): Transformative upgrade across all parameters

• vs. DS3800HSCB (high-speed analog): Similar high-speed capability; HITA1F1F offers improved accuracy, FIFO buffer, and F coating

• vs. DS3800HIMA1C1D (standard analog C1/D): HITA offers much higher sampling rate (1.5kHz vs. 60ms/16Hz) – HITA is for dynamic signals

• vs. ABB TB711 : ABB offers higher resolution (14-bit), but HITA1F1F offers higher sampling rate (1.5kHz vs. typically 100Hz on ABB), higher isolation (2500V vs. 1500V), FIFO buffer, and F coating

• vs. Siemens 7MH410 : Siemens offers HART protocol support, but GE HITA offers higher-speed sampling, FIFO buffering, and F-grade environmental protection

• vs. Woodward 8440-2015 : Woodward offers more flexible configuration, but GE HITA provides higher-speed capability, FIFO buffer, and F coating

• vs. Bently Nevada 3500/42 : Bently is vibration-dedicated with specialized processing; HITA is a general-purpose high-speed analog input

Selection Suggestions

• Critical: Confirm required sampling rate – HITA1F1F supports up to 1.5kHz; ensure this meets your dynamic signal requirements

• Verify your backplane provides both +5V and +15V – this board requires both rails

• Assess channel count – 4 differential channels may be sufficient for vibration/speed monitoring

• Evaluate if F1’s FIFO buffer and real-time noise profiling are beneficial – particularly valuable for transient analysis and critical protection applications

• Evaluate environmental conditions – F coating is suitable for frequent humidity and chemical exposure; choose G/H for more demanding conditions

• Order mating front connector (p/n may vary – confirm with GE)

• For critical protection applications, purchase with a calibration certificate and 12-month warranty

Precautions

• Critical: Do not exceed 30mA or ±30V on input channels – overvoltage may damage the ADC and isolation circuits

• Critical: High-speed sampling (1.5kHz) generates significant data – ensure the backplane and processor can handle the data throughput, especially when using FIFO buffer

• Critical: Use shielded twisted-pair cables for all analog inputs to avoid EMI – high-speed signals are particularly susceptible to noise; F1’s adaptive filtering helps but is not a substitute for good wiring practices

• Critical: Programmable filtering must be set correctly to avoid aliasing – consult the turbine control logic requirements

• Critical: FIFO buffer data capture requires proper configuration – ensure the buffer size and trigger settings match your analysis requirements

• Ensure field power supply (+24V DC) for loop-powered transmitters is stable (if used)

• F1 firmware offers adaptive anti-aliasing – configure jumpers correctly for your signal type and frequency range

• F coating provides good protection but is not suitable for direct salt spray, heavy chemical exposure, or continuous condensation – upgrade to G/H for those conditions

• Allow 45-minute warm-up before calibration (F coating affects thermal equilibrium)

• Store in ESD-safe packaging – edge connector is static-sensitive

• Periodically verify channel calibration every 1 year (high-speed applications may require more frequent verification)

• Do not hot-swap – Mark IV backplanes require power-off for insertion/removal

• If replacing a similar high-speed board, verify pinout compatibility – HITA may differ from HSCB or other high-speed series in wiring assignments

• F coating may make component-level repairs difficult – consider board replacement instead of repair