DS3800HAIC1E1C GE

Technical Specifications

• Product Type: High-Amplitude Isolated Current Output Board (Revision 1E1C)

• Part Number: DS3800HAIC1E1C

• Manufacturer: General Electric (GE)

• System Compatibility: GE Speedtronic Mark IV Turbine Control Systems (Rev. M and later)

• Output Channels: 4 independent isolated current outputs

• Output Type: 4-20mA or 0-20mA (jumper-selectable), loop-powered

• Drive Capability: Up to 130mA per channel (sourcing or sinking)

• Loop Power: Internal 24Vdc isolated loop power per channel (galvanically isolated)

• Compliance Voltage: 30Vdc (allows driving loads up to 750Ω at 20mA)

• Isolation Voltage: 2500Vrms reinforced isolation per channel (channel-to-channel and channel-to-logic) with enhanced common-mode transient immunity (> 90kV/µs)

• Resolution: 12-bit

• Accuracy: ±0.1% of full scale at 25°C; ±0.009% per °C drift

• Protection: Over-current, short-circuit, and reverse-polarity protection per channel

• Diagnostics: Individual channel fault detection (open-loop, short-circuit, over-temperature, load impedance variation, output drift) with LED indication and backplane reporting

• Temperature Range: -40°C to +82°C

• Heat Dissipation: Active thermal management with integrated heatsink, precision temperature sensor, and variable-speed cooling fan control output

• MTBF: > 210,000 hours (MIL-HDBK-217F)

Key Features & Advantages

• High Drive Capability: The GE DS3800HAIC1E1C delivers up to 130mA per channel for driving multiple devices in parallel or long cable runs.

• High Compliance Voltage: 30V compliance drives loads up to 750Ω at 20mA, accommodating a wide range of field devices.

• Per-Channel Reinforced Isolation: Provides 2500Vrms isolation per channel, eliminating ground loops and protecting logic from field-side faults.

• Advanced Diagnostics: Individual channel fault detection (open-loop, short-circuit, over-temperature, load impedance variation, output drift) with LED and backplane reporting for predictive maintenance.

• High Accuracy: ±0.009% per °C drift ensures precision in fluctuating temperatures.

• Active Thermal Management: Integrated temperature sensor and variable-speed fan control output ensure sustained high-current operation without thermal derating.

• Wide Temperature Range: -40°C to +82°C suits extreme environments.

• Enhanced Transient Immunity: > 90kV/µs common-mode transient immunity for superior noise rejection.

Typical Application Cases

• Explosive Atmospheres (Ex/ATEX): Provides galvanic isolation suitable for driving devices in hazardous areas with appropriate external barriers.

• Long-Distance Signal Transmission: Drives 4-20mA signals over distances up to 1500m with complete isolation.

• I/P (Current-to-Pressure) Converters: Drives I/P converters for pneumatic valve actuators with full isolation.

• Valve Positioners: Provides 4-20mA control signals for smart and analog positioners.

• Remote I/O Powering: Supplies isolated loop power and control signals to remote transmitters and actuators.

• Extreme Environment Installations: Wide temperature range suits offshore, arctic, or desert sites.

Competitive Comparison

The GE DS3800HAIC1E1C offers a balanced upgrade over the 1D1C with improved current, drift, and temperature range.

Selection Guidelines & Precautions

1. Isolation Requirements: Provides 2500Vrms per channel. Ensure this meets your system’s safety requirements.

2. Loop Configuration: Verify sourcing or sinking mode. Set jumpers accordingly.

3. Load Resistance: Calculate total loop resistance. Drives up to 750Ω at 20mA. Exceeding this causes saturation.

4. Loop Power: Each channel has isolated loop power. Ensure field devices do not have their own power supply.

5. Cable Length: Supports cables up to 1500m. For longer runs, reduce load or use a repeater.

6. Active Thermal Management: Connect the variable-speed fan control output to a cabinet cooling fan (24Vdc, < 500mA).

7. Diagnostic Reporting: Verify Mark IV firmware (Rev. M or later) supports backplane diagnostic reporting.

8. Load Impedance & Drift Monitoring: Familiarize yourself with fault codes for load impedance variation and output drift.

9. Short-Circuit Protection: Protected, but repeated shorting may affect reliability.

10. Commissioning: Use a precision current meter to verify each channel. Calibrate using onboard trimmers if necessary.

11. Wiring: Use shielded twisted-pair cables; ground shield at board end only. Do not connect shield to isolated output circuit.

12. ESD Handling: Use ESD-safe practices.

13. Sourcing: Obsolete. Request functional test report including:

    • All 4 channels tested at 4mA and 20mA

    • Load regulation test (up to 750Ω)

    • Loop power verification (30V per channel)

    • Isolation test (2500Vrms per channel, channel-to-channel)

    • Transient immunity test (> 90kV/µs)

    • Accuracy and drift test (±0.009%/°C)

    • Diagnostic fault reporting validation

    • Thermal management verification

14. Spare Strategy: Keep one spare GE DS3800HAIC1E1C on-site for critical isolated 4-20mA control applications. This revision offers excellent performance for demanding HAIC applications. If you require maximum current (150mA) or the best accuracy (±0.008%/°C), consider the DS3800HAIA1E1D. Proactive replacement after 10 years of continuous operation is recommended.